ult rafast switching rectifier voltage - 50 to 800 volts current - 10.0 amperes features ? plastic package has underwriters laboratory flammability classification 94v-o utilizing flame retardant epoxy molding compound ? exceeds environmental standards of mil-s-19500/228 ? low power loss, high efficiency ? low forward voltage, high current capability ? high surge capacity ? ultra fast recovery times, high voltage high temperature soldering : 260 ? o c / 10 seconds at terminals ? pb free product at available : 99% sn above meet rohs environment substance directive request mechancaldata ? case: ito-220ac full molded plastic package ? terminals: lead solderable per mil-std-202, method 208 ? polarity: as marked ? mounting position: any ? weight: 0.08 ounce, 2.26 gram maximum ratings and electrical characteristics ratings at 25 o c ? ambient temperature unless otherwise specified. single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate curr ent by 20% type number UF1000F uf1001f uf1002f uf1003f uf1004f uf1006f uf1008f units maximum recurrent peak reverse v oltage 50 100 200 300 400 600 800 v maximum rms voltage 35 70 140 210 280 420 560 v maximum dc blocking voltage 50 100 200 300 400 600 800 v maximum average forward rectif ied cur rent . 375? (9.5mm) lead length @ t c =100 10 a peak forward surge current , 8.3ms single half sine wave superimposed on rated load(j ecec method) 150 a maximum instantaneous forward voltage a t 10.0a 1.0 1.3 1.7 v maxi mum dc reverse current @t a =25 at rated dc blocking vol tage @t a =125 10.0 500 a maximum reverse recovery time(note 1) 50 75 ns typi cal junction capaci tance (note 2) 80 50 pf typi cal junction resi stance (note 2) r ja 15 operating and storage temperature range t j ,t stg -55 to +150 notes: 1. reverse recovery test conditions: if=0.5a, ir=1a, irr=0.25a 2. measured at 1 mhz and applied reverse voltage of 4.0 vdc 3. thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) p.c.b.mounted ito-220ac unit:inch(mm) .161(4.1) max .130(3.3) max .185(4.8) max .272(6.9) .248(6.3) .055(1.4) max .035(0.9) max .100(2.55) .543(13.8) .512(13. 0 ) .100(2.55) .114(2.9) .098(2.5) .032(0.8) max .606(15.4) .583(14.8) .112(2.85) .100(2.55) .406(10.3)max .134(3.4)dia .113(3.0)dia data sheet UF1000F~uf1008f semiconductor http://www.yeashin.com 1 rev.02 20110725 c c/w c c c
rating and characteristic curves note:1.rise time = 7ns max. in p ut im p edance = 1 me g ohm. 22 p f 2.rise time = 10ns max. source im p edance = 50 ohms t rr +0.5a 0 -0.25 -1.0 set time 1cm base for 50 ns/cm fig. 1-reverse recovery time characteristic and test circuit diagram 20 16 12 8 4 0 0 50 100 150 case temperature, fig. 1-typical forward current derating curve 1000 100 10 1.0 0.1 20 40 60 80 100 120 140 t j = 125 t j = 25 percent of rated peak reverse voltage fig. 2-typical reverse characteristics 150 120 90 60 30 1 2 5 10 20 50 100 tj = 125 8.3ms single half since- wave jedec method number of cycles at 60hz fig. 3-maximum non-repetitive forward surge current 210 200 160 120 80 40 0 1 2 5 20 50 100 200 500 UF1000F uf1008f reverse voltage, volts 80 40 20 10 3.0 1.0 0.3 0.1 0.03 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.8 UF1000F uf1008f forward voltage, volts fig. 4-typical junction capacitance fig. 5-typical forward characteristics peak forward current, amperes instantaneous reverse current, microamperes peak forward current amperes capacitance, (pf) instantaneous forward current, (a) UF1000F~uf1008f http://www.yeashin.com 2 rev.02 20110725 c c c c
|
